Announcement

Collapse
No announcement yet.

Using paint as your aquarium background

Collapse
X
Collapse
  •  

  • Using paint as your aquarium background

    Background color choice may depend on your type of tank, and more importantly your fish. Eg. many blue discus tend to darken with a black background or pepper up in the case of pigeon blood colors (something about the appearance of the void may frighten them). Some Tropheus, like Moliro reds, may not show their brightest color with a black background (unless you've got some nice white gravel). However, blue can be quite blaring (this is subjective), especially on a tank without much front to back space and lighting towards the rear instead of at the front (works better on bigger tanks). Some of the lighter colored fish, such as platinum angelfish or small tetras, seem to get drowned out. Now, black works well with cardinal tetras, platinum/silver colored fish (bala sharks, platinum angelfish), electric blue haps. I've found lighter blue works well with discus, black colored fish like mollies and black angelfish. I'd suggest buying some different colored boards and taping them to the back of the tank to get an idea. Alternatively, I've used an pastel green, it looks awesome (very natural looking if you've got a deep tank from front to back).

    As for paint, I've used Krylon and Rustoleum, they last. Currently, since all my tanks are nanos now (prior the smallest thing I had was a 50 gallon sump for my smallest tank 250gal- so it pays to planout backgrounds) I buy either colored foam sheets/paper (at Micheal's), or a roll of rubber kitchen drawer liner (comes in black,beige, and white at Lowe's) to clip or tape onto the back of my tanks. When you do paint your tank, especially if it's a large one, having a flashlight or small lamp may be handy, to check for areas where the paint may not be thick enough. Spray on thin coats at a time. Take frequent breaks and wear a mask, this stuff is MUCHO TOXIC!
      Posting comments is disabled.

    Latest Articles

    Collapse

    • Building a Canopy for a 125 Gallon Tank
      by Hangman
      Well, its 2 AM and I just got pretty much done with the canopy.

      Supplies:

      1 4x8 plywood (red oak)
      16 ft. large molding trim
      16 ft small molding trim
      17 ft smal angle modling trim (to make the cabinet doors)
      2 sets of hinges.

      1st: Cut the ply wood into strips to make the front and side of the cabinet:


      P9020006 by HangTheMan, on Flickr

      2nd: Make sure the edges of the strips are 45 degrees to make ...
      09-03-2012, 01:49 PM
    • Horizontal Tank Divider
      by ScorpiosWife
      OK, so the entire thing took about 20 minutes to build! Of course, as I suspected, hubby wouldn't let me play with sharp objects. While he was cutting, I removed the filter, gathered some marbles for the sides & then realized I forgot to take pictures of the material before we started. Oops. I didn't remember till he had already cut the mesh, egg crate & had started with the zip ties. Hubby measured & cut the egg crate as close to the inner dimension of the tank as possible. Then he cut the ...
      08-22-2012, 07:50 PM
    • DIY LED Build
      by cichlid1409
      So, I've been wanting to upgrade to a LED fixture on my coral tank for a while now. As I looked online at all the fixtures I found they were either too much moolah or not bright enough IMO. So I decided to pull the trigger and try to build my own. After digging around online and figuring out a game plan this is what I decided to go with: 12 - 3w cree XP-G (white) 12 - 3w cree XP-E (royal blue) 1 - meanwell 35-700 driver 1 - meanwell 60-1050 driver 60 degree lenses 10in X 10in heatsink Custom ...
      03-24-2011, 12:22 PM
    • Continual Air Removal From Siphon Tubes On Overflow Box
      by jarrodaden
      I was looking for a way to automate the air removal from the siphon tubes on my overflow box without running risk of pumping the siphon tubes empty. I was also worried about siphoning them dry during a power outage via the air tube.

      Using an aqua-lifter pump, I came up with a solution.

      Attached is a DIY video link.

      ...
      09-26-2010, 03:11 PM
    • Wet/dry Filter Outlet Anti-Siphon Hole - Shield preventing messy spitting at startup
      by jarrodaden


      I had a problem with water squirting out the anti-siphon hole on my wet/dry outlet and Dustin at Houston Aquarium Warehouse gave me this idea.

      Simple and easy to do.


      ...
      09-26-2010, 01:21 PM
    • DIY Background- Vinyl
      by Zebvance
      I had a black background on my 240 from Petsmart. I had a lot of problems with it. Water would get in between the background and the tank when I would service the tank. It got on my nerves enough for me to rip it off. I ended up having the idea of laying down one big piece of vinyl (a big black sticker) on the back instead of painting it. I am not a very good painter and I didn't want to do something that permanent to my tank. So I picked up a 96x30 sheet of vinyl from the local decal shop...
      08-28-2010, 01:25 PM
    Working...
    X