Announcement

Collapse
No announcement yet.

Continual Air Removal From Siphon Tubes On Overflow Box

Collapse
X
Collapse
  •  

  • Continual Air Removal From Siphon Tubes On Overflow Box

    I was looking for a way to automate the air removal from the siphon tubes on my overflow box without running risk of pumping the siphon tubes empty. I was also worried about siphoning them dry during a power outage via the air tube.

    Using an aqua-lifter pump, I came up with a solution.

    Attached is a DIY video link.


    • snookfish
      #1
      snookfish commented
      Editing a comment
      The biggest reason for air being trapped in an overflow siphon is not enough flow. as long as the flow rate is high enough, air doesn't have the ability to become trapped.

    • jarrodaden
      #2
      jarrodaden commented
      Editing a comment
      This is true, but with a dual siphon setup (in my experience) one of the tubes becomes the dominant one and the second will slow in flow considerably and occassionally fail all together (loosing the siphon).

      My setup works well and it is one less thing for me to worry about. Also, during a power loss if I lose the siphon it will automatically re-establish the siphon when the power kicks back on.
    Posting comments is disabled.

Latest Articles

Collapse

  • Building a Canopy for a 125 Gallon Tank
    by Hangman
    Well, its 2 AM and I just got pretty much done with the canopy.

    Supplies:

    1 4x8 plywood (red oak)
    16 ft. large molding trim
    16 ft small molding trim
    17 ft smal angle modling trim (to make the cabinet doors)
    2 sets of hinges.

    1st: Cut the ply wood into strips to make the front and side of the cabinet:


    P9020006 by HangTheMan, on Flickr

    2nd: Make sure the edges of the strips are 45 degrees to make ...
    09-03-2012, 01:49 PM
  • Horizontal Tank Divider
    by ScorpiosWife
    OK, so the entire thing took about 20 minutes to build! Of course, as I suspected, hubby wouldn't let me play with sharp objects. While he was cutting, I removed the filter, gathered some marbles for the sides & then realized I forgot to take pictures of the material before we started. Oops. I didn't remember till he had already cut the mesh, egg crate & had started with the zip ties. Hubby measured & cut the egg crate as close to the inner dimension of the tank as possible. Then he cut the ...
    08-22-2012, 07:50 PM
  • DIY LED Build
    by cichlid1409
    So, I've been wanting to upgrade to a LED fixture on my coral tank for a while now. As I looked online at all the fixtures I found they were either too much moolah or not bright enough IMO. So I decided to pull the trigger and try to build my own. After digging around online and figuring out a game plan this is what I decided to go with: 12 - 3w cree XP-G (white) 12 - 3w cree XP-E (royal blue) 1 - meanwell 35-700 driver 1 - meanwell 60-1050 driver 60 degree lenses 10in X 10in heatsink Custom ...
    03-24-2011, 12:22 PM
  • Continual Air Removal From Siphon Tubes On Overflow Box
    by jarrodaden
    I was looking for a way to automate the air removal from the siphon tubes on my overflow box without running risk of pumping the siphon tubes empty. I was also worried about siphoning them dry during a power outage via the air tube.

    Using an aqua-lifter pump, I came up with a solution.

    Attached is a DIY video link.

    ...
    09-26-2010, 03:11 PM
  • Wet/dry Filter Outlet Anti-Siphon Hole - Shield preventing messy spitting at startup
    by jarrodaden


    I had a problem with water squirting out the anti-siphon hole on my wet/dry outlet and Dustin at Houston Aquarium Warehouse gave me this idea.

    Simple and easy to do.


    ...
    09-26-2010, 01:21 PM
  • DIY Background- Vinyl
    by Zebvance
    I had a black background on my 240 from Petsmart. I had a lot of problems with it. Water would get in between the background and the tank when I would service the tank. It got on my nerves enough for me to rip it off. I ended up having the idea of laying down one big piece of vinyl (a big black sticker) on the back instead of painting it. I am not a very good painter and I didn't want to do something that permanent to my tank. So I picked up a 96x30 sheet of vinyl from the local decal shop...
    08-28-2010, 01:25 PM
Working...
X